Blade Application Guides / Application Guide / Semiconductor assembly
Conductive Chip-Tray Sheet Shear Slitting Blades
Conductive Chip-Tray Sheet is a cleanroom tape, release film or interleaf whose particle level, release behavior and dimensional stability are tightly controlled. During shear slitting, the objective is to divide moving stock with an overlapped upper and lower rotary blade pair while preventing adhesive transfer, particles, liner cut-through, wrinkles or release-force variation. Blade selection should follow samples, machine drawings and measurable acceptance criteria rather than the material name alone.
Updated
Where This Cutting Application Appears
Semiconductor assembly production
Conductive Chip-Tray Sheet is processed by shear slitting to support wafer handling, molding release, leadframe protection and contamination-controlled transport. The finished result must remain compatible with downstream handling, inspection and assembly.
Cut-quality control
Production teams compare accepted and rejected samples for cut completeness, particle level, release surface, registration, liner condition and dimensional accuracy, then relate the result to side clearance, overlap, runout, holder alignment, web tension and edge support.
Stable material and waste handling
Cleanroom-compatible contact, low static, stable tension and protected sample collection help the product and waste leave the cut zone consistently without creating a second defect after separation.
Shear Slitting process boundary
Shear slitting uses an overlapped rotary blade pair and controlled side clearance; it differs from unsupported razor penetration.
Production setup checkpoint
Record the starting setup for side clearance, overlap, runout, holder alignment, web tension and edge support, then change one controlled variable at a time and retain samples from each trial condition.
Cut-quality acceptance checkpoint
Approve the result against measured cut completeness, particle level, release surface, registration, liner condition and dimensional accuracy after the sample has reached the same handling or conditioning state used by the next production step.
Define the Required Cut Result
- Achieve parallel slit widths with low burr, dust and edge deformation for conductive chip-tray sheet
- Prevent adhesive transfer, particles, liner cut-through, wrinkles or release-force variation
- Maintain the required geometry for wafer handling, molding release, leadframe protection and contamination-controlled transport
- Deliver a cut condition accepted by the next semiconductor assembly operation
Problems to Diagnose Before Changing the Knife
The processed material shows adhesive transfer, particles, liner cut-through, wrinkles or release-force variation
- Compare blade condition and clearance.
- Check side clearance, overlap, runout, holder alignment, web tension and edge support.
- Separate material-lot effects from machine effects.
Finished dimensions drift during a production run
- Check feed registration and tension or hold-down.
- Measure runout, temperature and support condition.
- Record when dimensions are measured after cutting.
The workpiece shifts, curls or loses functional surface quality
- Review cleanroom-compatible contact, low static, stable tension and protected sample collection.
- Confirm material direction and contact-face cleanliness.
- Identify the first point where deformation appears.
Product and waste do not separate consistently
- Check cut completeness and waste width.
- Review exit angle, static and extraction.
- Inspect downstream transfer and collection tension.
Knife Forms That May Be Considered
| Possible knife form | When it may be considered | What must be confirmed |
|---|---|---|
| Matched circular slitter pair | Considered when shear slitting requires parallel slit widths with low burr, dust and edge deformation under stable support and guidance. | Confirm only after reviewing a real conductive chip-tray sheet sample, the equipment interface, mounting drawing, operating direction and an accepted cut reference. |
| Dished shear slitter blade | Considered when the equipment interface and material response require an alternative geometry or cutting motion. | Confirm only after reviewing a real conductive chip-tray sheet sample, the equipment interface, mounting drawing, operating direction and an accepted cut reference. |
Information to Send for Technical Review
You do not need to know the exact blade name. Send the available workpiece, machine, current-knife and cut-result information so the application can be reviewed against a drawing or sample.
- Conductive Chip-Tray Sheet composition, grade, thickness and allowable lot variation
- Layer, coating, temper, adhesive or surface-function details relevant to shear slitting
- Input width and target dimensions, tolerances and acceptance drawing
- Line speed, feed mode, tension or hold-down, temperature and cutting frequency
- Current blade or knife drawing, holder interface, mounting dimensions and used sample
- Material direction, support, contact faces and product or waste collection method
- Accepted and rejected samples with limits for cut completeness, particle level, release surface, registration, liner condition and dimensional accuracy
- Trial quantity, inspection method, downstream operation, packing and annual demand
Questions About This Cutting Application
Why must conductive chip-tray sheet be reviewed as a complete material construction?
Its layers, surface condition and mechanical response can react differently to pressure, friction, heat and bending, so nominal thickness alone does not predict shear slitting performance.
Can the blade be selected from the material name alone?
No. Confirm side clearance, overlap, runout, holder alignment, web tension and edge support, the holder interface, production speed, support and accepted samples before fixing blade material or edge geometry.
What commonly causes defects during shear slitting?
Material variation, unstable support, alignment error, contamination, inappropriate clearance and blade wear can interact to create adhesive transfer, particles, liner cut-through, wrinkles or release-force variation.
When should the finished result be measured?
Record both immediate and conditioned results when recovery, residual stress, temperature, moisture or adhesive flow can change the workpiece after cutting.
What should be recorded during a production trial?
Record the conductive chip-tray sheet lot, setup, speed, support, blade condition, dimensions, edge observations, waste behavior and downstream acceptance.
Related product and service information
- Leadframe Protective Cover Tape Razor Slitting Blades - leadframe protective cover tape · razor slitting
- UV-Release Wafer Dicing Tape Shear Slitting Blades - UV-release wafer dicing tape · shear slitting
- Semiconductor Molding Release Film Shear Slitting Blades - semiconductor molding release film · shear slitting
Request a Custom Cutting-Knife Review
Send the workpiece details, machine or holder information, current knife photos or sample, required quantity and examples of the present cut problem. Final dimensions, material, edge geometry and tolerances are confirmed from the approved requirements.